- 3 Port Reference for Non Redundant Network VS Zero Switch-Over Reliable Network -

All hardware low-latency switch for FPGAs

HSR-PRP Switch (HPS) is an IP Core for the implementation of High-availability Seamless Redundancy and Parallel Redundancy Protocol (HSR and PRP version 3, IEC 62439-3-Clause 5 and 4 respectively) standards for Reliable Ethernet communications. HSR-PRP Switch is a full hardware solution that can be implemented on a low-cost FPGA.

It is a flexible solution for the Energy Market Equipment that will be connected to HSR rings, PRP Lans or will work as Network bridges in the context of IEC 61850.

HSR-PRP Switch IP core key features:

  • Fast Ethernet and Gigabit Ethernet supported: 10/100/1000TX -1000FX
  • It supports up to 12 ports
  • It switches frames by hardware. This feature offers high switching speeds, needed to fulfill the Maximum Allowed Age and Data Integrity set for Process Bus and Inter-bay Bus in Electric Substation Automation
  • The processing architecture has been designed specifically for HSR/PRP. Forwarding latencies in range of 500ns for Gigabit Ethernet
  • It is an all-hardware. There is no need for on-chip microprocessor nor software stack
  • It has been optimized to require few logic resources in order to allow the implementation on low-cost FPGA devices
  • It supports IEEE 1588-2008 v2 combined with SoC-e 1588 IP cores
  • It can be used to implement End-Node DAN, RedBox or QuadBox functionalities
  • It has been provided with a single flag that switches between PRP and HSR modes by software
  • It includes complete statistics and error registers for each port integrated (Network Supervision)
  • Supported HSR modes: H, N, T, U,X
  • Supported PRP modes: Duplicates Discard, Duplicates Accept
  • HSR-HSR, HSR-PRP supported modes for seamless PRP-HSR networks merging and Quadbox operation
  • VLAN support and HSR Rings id
  • Evaluation Designs for Spartan-6 and Zynq devices
  • SMNP and MIB Table available
  • Configuration-over-Ethernet (COE): Full access to internal registers through the same Ethernet link that connects to the CPU
  • Dynamic Bitstream Configuration: Allows changing remotely the functionality of the FPGA

HSR-PRP Switch IP core customizable features for optimum resources/functionalities trade off:

  • Node Table size
  • Forwarding Queues size independent for each port
  • IEEE1588v2 P2P Transparent Clock in Redundant and Interlink Ports
  • Scalable duplicate/circulate discard table
  • VLAN Priority support
  • Access to internal registers via MDIO or UART
  • RedBox mode with integrated SAN proxy
  • IEEE 1588v2 Ordinary Clock, Hybrid Clock and Boundary Clock

Supported boards for the Reference Designs:

  • Featured boards:
  • Other boards:
    • Xilinx Zynq ZC702 Evaluation Board
    • Fast Ethernet: Xilinx SP605 Evaluation Board andISM Networking FMC Module
    • Gigabit Ethernet: Xilinx SP605 Evaluation Board and 1000 Base-T Ethernet FMC Card By Inrevium FMC module
    • Avnet Industrial Ethernet Kit

Features implemented on the Reference Designs:

  • Standard version of HSR-PRP Switch implements DAN-RedBox topology
  • Zynq Reference Design implements a full DAN-Redbox topology using Internal Link to ARM9 Processor and an external port to attach conventional Ethernet LAN.

Pricing, Availability and Ordering

  • Concurrent EDA is the US Distributor for SoC-e.
  • Currently shipping to US customers.
  • Please email Ray Hoare at This e-mail address is being protected from spambots. You need JavaScript enabled to view it with questions / quotes / orders.


5001 Baum Blvd Ste 640
Pittsburgh PA 15213